Dynomotion

Group: DynoMotion Message: 14785 From: 8cc4913a51932ba22d57c0384f630f10 Date: 5/18/2017
Subject: Slide Goes to Strange Location

Hi Tom,

Working on a machine and using a simple gcode for slide testing...


G1 X5 F70
G1 Y1
G1 X1
G1 X0 Y0
M30


The machine moves as it should, but after the final X0 Y0 it moves to X2.6173 Y1.7440 and parks there. There are no offsets set, but it seems if a load another test file it also executes and then goes to these coordinates to finish. Any suggestions?


Thanks, David.
Group: DynoMotion Message: 14786 From: Moray Cuthill Date: 5/18/2017
Subject: Re: Slide Goes to Strange Location
Have you got anything set for M30 in Tool Setup?

Moray

Virus-free. www.avast.com

On Thu, May 18, 2017 at 10:20 PM, david.m.stevenson@... [DynoMotion] <DynoMotion@yahoogroups.com> wrote:
 

Hi Tom,

Working on a machine and using a simple gcode for slide testing...


G1 X5 F70
G1 Y1
G1 X1
G1 X0 Y0
M30


The machine moves as it should, but after the final X0 Y0 it moves to X2.6173 Y1.7440 and parks there. There are no offsets set, but it seems if a load another test file it also executes and then goes to these coordinates to finish. Any suggestions?


Thanks, David.
Group: DynoMotion Message: 14787 From: David Stevenson Date: 5/18/2017
Subject: Re: Slide Goes to Strange Location
No, it's set to "none" which I expect acts as the usual rewind, since it does rewind to the first line. But thanks.

On 5/18/2017 5:35 PM, Moray Cuthill moray.cuthill@... [DynoMotion] wrote:
 
Have you got anything set for M30 in Tool Setup?

Moray

Virus-free. www.avast.com

On Thu, May 18, 2017 at 10:20 PM, david.m.stevenson@... [DynoMotion] <DynoMotion@yahoogroups.com> wrote:
 

Hi Tom,

Working on a machine and using a simple gcode for slide testing...


G1 X5 F70
G1 Y1
G1 X1
G1 X0 Y0
M30


The machine moves as it should, but after the final X0 Y0 it moves to X2.6173 Y1.7440 and parks there. There are no offsets set, but it seems if a load another test file it also executes and then goes to these coordinates to finish. Any suggestions?


Thanks, David.
Group: DynoMotion Message: 14788 From: Tom Kerekes Date: 5/18/2017
Subject: Re: Slide Goes to Strange Location

Hi David,

Any C Programs running in KFLOP?

Regards
TK

On 5/18/2017 4:19 PM, David Stevenson david.m.stevenson@... [DynoMotion] wrote:
 

No, it's set to "none" which I expect acts as the usual rewind, since it does rewind to the first line. But thanks.

On 5/18/2017 5:35 PM, Moray Cuthill moray.cuthill@... [DynoMotion] wrote:
 
Have you got anything set for M30 in Tool Setup?

Moray

Virus-free. www.avast.com

On Thu, May 18, 2017 at 10:20 PM, david.m.stevenson@... [DynoMotion] <DynoMotion@yahoogroups.com> wrote:
 

Hi Tom,

Working on a machine and using a simple gcode for slide testing...


G1 X5 F70
G1 Y1
G1 X1
G1 X0 Y0
M30


The machine moves as it should, but after the final X0 Y0 it moves to X2.6173 Y1.7440 and parks there. There are no offsets set, but it seems if a load another test file it also executes and then goes to these coordinates to finish. Any suggestions?


Thanks, David.
Group: DynoMotion Message: 14789 From: David Stevenson Date: 5/18/2017
Subject: Re: Slide Goes to Strange Location
Hi Tom,
There wasn't, that I was aware of other than the init program, but I just re-initialized and everything seems okay. Guess I should have tried that earlier.

Thanks and sorry to be a bother,
David.

On 5/18/2017 7:25 PM, Tom Kerekes tk@... [DynoMotion] wrote:
 

Hi David,

Any C Programs running in KFLOP?

Regards
TK

On 5/18/2017 4:19 PM, David Stevenson david.m.stevenson@... [DynoMotion] wrote:
 

No, it's set to "none" which I expect acts as the usual rewind, since it does rewind to the first line. But thanks.

On 5/18/2017 5:35 PM, Moray Cuthill moray.cuthill@... [DynoMotion] wrote:
 
Have you got anything set for M30 in Tool Setup?

Moray

Virus-free. www.avast.com

On Thu, May 18, 2017 at 10:20 PM, david.m.stevenson@... [DynoMotion] <DynoMotion@yahoogroups.com> wrote:
 

Hi Tom,

Working on a machine and using a simple gcode for slide testing...


G1 X5 F70
G1 Y1
G1 X1
G1 X0 Y0
M30


The machine moves as it should, but after the final X0 Y0 it moves to X2.6173 Y1.7440 and parks there. There are no offsets set, but it seems if a load another test file it also executes and then goes to these coordinates to finish. Any suggestions?


Thanks, David.